17CrNiMo6
2015-01-26 09:34:07 Origin: Remark:0 Click:
Inventory 17CrNiMo6 Round bar, Stocklist 1.6587 Suppliers, Specifications 17CrNiMo6 properties from steelmaking, ESR, blooming, forging, rolling, heat treatment, straightened, ultrasonic test, cold working, machined. We also possess advanced precision machining equipments for further processing.
Material specification - DIN EN 10084 (1998), DIN 17210 (1986)
TECHNICAL SPECIFICATION - DIN 17CrNiMo6 & W-Nr 1.6587
Official Test Certificate: issued by TUV - SGS - BV
MATERIAL CATEGORY - Carburizing structural steel
PRODUCT DESCRIPTION
Proven performance in long-term service.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
Extensive database of long term, high temperature test results.
High room and elevated temperature strength.Good creep.
High notch tolerance.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Thermal expansion coefficients compatible with low alloy steel turbine casing materials.
Lower design and operating risks
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Simplified design for bolting configuration compared with martensitic steels or high nickel alloys.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
MATERIAL SPECIFICATIONS - DIN EN 10084 (1998), DIN 17210 (1986)
CHEMICAL COMPOSITION ( Mass weight - % )
C (%): 0.15 ~ 0.21
Si (%): ≤ 0.40
Mn (%): 0.50 ~ 0.90
P (%)≤: 0.025
S (%)≤: 0.015
Cr (%): 1.50 ~ 1.80
Mo (%): 0.25 ~ 0.35
Ni (%): 1.40 ~ 1.70
Other (%): Al ≤0.05, Cu ≤0.30
Si (%): ≤ 0.40
Mn (%): 0.50 ~ 0.90
P (%)≤: 0.025
S (%)≤: 0.015
Cr (%): 1.50 ~ 1.80
Mo (%): 0.25 ~ 0.35
Ni (%): 1.40 ~ 1.70
Other (%): Al ≤0.05, Cu ≤0.30
MECHANICAL PROPERTIES - HOT WORKING, HEAT TREATMENT AND HARDNESS
Hot working temperature /℃: 1150~850
Heat treatment temperature /℃| annealing: 650~700
Heat treatment temperature /℃|carburization: 880~980
Heat treatment temperature /℃|quenchingⅠ(center): 830~870
Heat treatment temperature /℃|quenchingⅡ(surface): 780~820, Oil
Heat treatment temperature /℃|tempering: 150~200
Heat treatment temperature /℃| annealing: 650~700
Heat treatment temperature /℃|carburization: 880~980
Heat treatment temperature /℃|quenchingⅠ(center): 830~870
Heat treatment temperature /℃|quenchingⅡ(surface): 780~820, Oil
Heat treatment temperature /℃|tempering: 150~200
HBW≤: 229
|size /mm: φ11
TS, |σb/MPa: 1180~1420
YS, |σs≥/MPa: 835
EL, |δ5(%)≥: 7.0
RA, |ψ(%)≥: 30
Impact, |AKV/J 41
|size /mm: φ11
TS, |σb/MPa: 1180~1420
YS, |σs≥/MPa: 835
EL, |δ5(%)≥: 7.0
RA, |ψ(%)≥: 30
Impact, |AKV/J 41
|size /mm: φ30
TS, |σb/MPa: 1080~1330
YS, |σs≥/MPa: 785
EL, |δ5(%)≥: 8.0
RA, |ψ(%)≥: 35.0
Impact, |AKV/J: 41
TS, |σb/MPa: 1080~1330
YS, |σs≥/MPa: 785
EL, |δ5(%)≥: 8.0
RA, |ψ(%)≥: 35.0
Impact, |AKV/J: 41
|size /mm: φ63
TS, |σb/MPa: 980~1270
YS, |σs≥/MPa: 685
EL, |δ5(%)≥: 8.0
RA, |ψ(%)≥: 35.0
Impact, |AKV/J: -
TS, |σb/MPa: 980~1270
YS, |σs≥/MPa: 685
EL, |δ5(%)≥: 8.0
RA, |ψ(%)≥: 35.0
Impact, |AKV/J: -
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods
Process plant – fasteners
Process plant – fasteners
Mechanical gears, gear shaft, main axis, valve rod
Mechanical parts - connecting rod, bolts and nuts
Multidiameter shaft
Pressure vessel, seamless pipe
PRODUCT PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 1000mm X W50 - 1000mm X L1000 - 5000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers. E-mail: sales@ccsteels.com
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers. E-mail: sales@ccsteels.com
Hot search:17CrNiMo6
Previous page:18CrNiMo7-6
Last page:14NiCrMo13-4
Total list
Monthly rank
- 37EN23
- 21S99
- 2127NiCrMoV11-6
- 2026NiCrMoV14-5
- 2015NiCuMoNb5
- 19D6AC
- 19A470 Grade D Class 8
- 18EN19C
- 1815CrNi6
- 171.7223