EN 29B
2015-07-13 10:45:03 Origin: Remark:0 Click:
Description EN 29B Round bar, Suppliers EN29B Stocklist, Forgings EN 29B Properties steelmaking, Electroslag melting, Hot rolling, Heat treatment
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
TECHNICAL SPECIFICATION DATASHEET - Grade EN 29B
MATERIAL CATEGORY - Aircraft "S" series alloy structural steel
TYPE OF STEEL - 3% Cr-Mo Steel
MELTING PROCESS - EAF + VD + LF / BEF / VIM + ESR
H S CODE For Customs - 7228 4000 / 7228 5000 / 7228 6000
H S CODE For Customs - 7228 4000 / 7228 5000 / 7228 6000
CHEMICAL COMPOSITION (Mass weight - %)
Carbon, C (%): 0.20 ~ 0.35
Silicon, Si (%): 0.10 ~ 0.35
Manganese, Mn (%): ≤ 0.65
Phosphorus, P (%) ≤: 0.035
Sulfur, S (%) ≤: 0.030
Chromium, Cr (%): 2.50 ~ 3.50
Silicon, Si (%): 0.10 ~ 0.35
Manganese, Mn (%): ≤ 0.65
Phosphorus, P (%) ≤: 0.035
Sulfur, S (%) ≤: 0.030
Chromium, Cr (%): 2.50 ~ 3.50
Nickel, Ni (%): ≤ 0.40
Molybdenum, Mo (%): 0.30 ~ 0.70
Molybdenum, Mo (%): 0.30 ~ 0.70
Equal to: EN 29A, EN 29B
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Condition: Heat treatment
Tensile strength σb≥/MPa: 1130
Yield strength σs≥/MPa: 835
Elongation δ5≥(%): 10.0
Yield strength σs≥/MPa: 835
Elongation δ5≥(%): 10.0
Impact strength, AKv ≥/J: -
Hardness HBS: 240 min.
Hardness HBS: 240 min.
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF / VD / LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
The alloy is usually produced by EAF / VD / LF followed by electroslag refining (ESR) if necessary for special purpose. Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - Quenched and tempered.
PROFILE & AVAILABLE SIZE
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Round bar / Wire rod (Diameter): 5.5mm to 550mm
Square bar / Flat bar: 3mm to 800mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 400mm X W50 - 1000mm X L1000 - 12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shaft, and other different shapes based on OEM.
Sheet steel via cold rolled: T0.5 - 6mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shaft, and other different shapes based on OEM.
TYPICAL APPLICATIONS
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel.
Alloy structural steels are widely used in the filed of ship, vehicle, airplane, guided missile, weapons, railway, bridges, pressure vessel, machine tools, mechanical components with a bigger sectional size and so on.
Power generation – turbine fasteners – boiler support rods.
Process plant – fasteners, Mechanical gears, gear shaft, main axis, valve rod.
Mechanical parts - connecting rod, bolt and nut, Multidiameter shaft, Pressure vessel.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, Email: sales@ccsteels.com
Total list
Monthly rank
- 3624CrMo5
- 3338NCD4
- 33EN 14B
- 3342Cr4Mo2
- 28EN33 / EN 33
- 27ASTM A739 type B11
- 22EN 38
- 22XC38
- 2231Ni10Cr3Mo6
- 2226NiCrMoV11-5