AMS 5875
2020-04-21 10:59:48 Origin： Remark：0 Click：
AMS 5875 datasheet, Ex-stock AMS 5875 Suppliers, AMS 5875 Forge bar plate machined, Alloy AMS 5875 exporters, from Melting, ESR & VAR technique, Blooming, Hot forging, Hot rolling, Heat treatment, Straightening, 100% Ultrasonic flaw detection test,
TECHNICAL DATA SHEET - AMS 5875
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
MATERIAL CATEGORY: Ni - Cr - Co - Fe Superalloy
Elgiloy ( AMS 5875 Co-Cr-Ni Alloy) is a "super-alloy" consisting of 39-41% Cobalt, 19-21% Chromium, 14-16% Nickel, 11.3-20.5% Iron, 6-8% Molybdenum, and 1.5-2.5% Manganese.
It is used to make springs that are corrosion resistant and exhibit high strength, ductility, and good fatigue life. Due to its chemical composition, Elgiloy is highly resistant to sulfide stress corrosion cracking and pitting, and can operate at temperatures up to 454°C.
It is used to make springs that are corrosion resistant and exhibit high strength, ductility, and good fatigue life. Due to its chemical composition, Elgiloy is highly resistant to sulfide stress corrosion cracking and pitting, and can operate at temperatures up to 454°C.
CHEMICAL COMPOSITION (WEIGHT %)
C (％): ≤ 0.15
C (％): ≤ 0.15
Si (％): ≤ 1.00
Mn (％): 1.50 ~ 2.50
P (％)≤: 0.025
Mn (％): 1.50 ~ 2.50
P (％)≤: 0.025
S (％)≤: 0.015
Cr (％): 19.0 ~ 21.0
Cr (％): 19.0 ~ 21.0
Ni (％): 14.0 ~ 16.0
Mo (％): 6.00 ~ 8.00
Co (%): 39.0 ~ 41.0
Co (%): 39.0 ~ 41.0
W (%): 2.30 ~ 3.30
Al (%): -
Al (%): -
Cu (%): -
Ti (%): -
Ti (%): -
Fe (%): 11.0 ~ 20.5
Be (%): ≤ 0.10
TYPICAL MECHANICAL PROPERTIES
Tensile strength, σb/≥ MPa: 860
Yield strength, σ0.2/MPa: 520
Elongation, δ ≥(％): 30.0
Reduction of area, ф ≥ (％): -
Hardness via heat treatment /HBW: -
Reduction of area, ф ≥ (％): -
Hardness via heat treatment /HBW: -
FORMS AND SHAPES
Round bar (Diameter): 5.50 ~ 450mm
Square bar / Flat bar: 3 ~ 350mm
Round bar (Diameter): 5.50 ~ 450mm
Square bar / Flat bar: 3 ~ 350mm
Wire rod (Diameter): 0.10 ~ 16mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 650mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
Steel strip via cold rolled: T0.1 - 3mm X W5 - 650mm X L (or in coil form)
Forging piece: Different shapes based on OEM.
Other sizes can be supplied to meet specific requirements.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to Email our qualified production engineers. - Email: sales@ccsteels.com
If you meet further on any technical enquiry, pleased to Email our qualified production engineers. - Email: sales@ccsteels.com
Total list
Monthly rank
- 50FSX-414
- 16Aquamet 22
- 1510705BU
- 15AMS 5221
- 13Carpenter 20 Mo 4
- 12X12CrNiMoV12-2
- 11Inconel 610
- 10AMS 5354
- 9Incoloy 840
- 8Aquamet 17
